Effect of styrene-methyl methacrylate/styrene-butadiene rubber on properties of poly(vinyl chloride)

Authors

  • Buranin Saengiet Faculty of Science, Chulalongkorn University
  • Fuangfa Unob Faculty of Science, Chulalongkorn University
  • Kawee Srikulkit Faculty of Science, Chulalongkorn University

Keywords:

SMMA/SBR rubber compound, Impact modifier, PVC

Abstract

Generally, poly(vinyl chloride) (PVC) without the addition of plasticizer or impact modifiers is rigid and brittle. The aim of this research was to improve the mechanical properties of PVC using styrene-methyl methacrylate/styrene-butadiene compound (SMMA/SBR rubber) as an impact modifier. The compound was obtained commercially.  PVC containing SMMA/SBR rubber having SMMA/SBR phrs of 2.5, 5, 7.5 and 10 were prepared using two-roll mill set the conditions as follows: 170 oC and 5 min. Then, compression molding was carried out to prepare testing samples. FTIR analysis of SMMA/SBR rubber containing PVC samples showed the absorption band at 1732 cm-1 (C=O stretching), 3025 cm-1 (=C-H stretching) and 636.8 cm-1 (C-Cl band). The effects of SMMA/SBR rubber on mechanical properties, including impact strength and tensile properties were evaluated by standard tests. The impact strength of SMMA/SBR rubber containing PVC increased significantly with an increase in the SMMA/SBR content (ex. SMMA/SBR 5 phr and 10 phr produced 3.30 and 6.38 kJ/m2 respectively), resulting from the action of SMMA/SBR rubber phase as impact modifier as revealed by SEM images. Furthermore, modulus, tensile strength and elongation at break were investigated.

Downloads

Download data is not yet available.

References

Hosseinpour, P.M., Morshedian, J., Barikani, M., Azizi, H. and Pakdaman, A.S. (2010). Morphological, mechanical, and rheological studies of PVC/ABS blends in the presence of maleic anhydride. J. Vinyl. Addit. Technol. 16(2) : 127-134.

Pena, J. R., Hidalgo, M. and Mijangos, C. (2000). Plastification of poly (vinyl chloride) by polymer blending. J. Appl. Polym. Sci. 75(10) : 1303-1312.

Rimdusit, S., Wongmanit, P., Damrongsakkul, S., Saramas, D., Jubsilp, C. and Dueramae, I. (2014). Characterizations of Poly (vinyl chloride) /Acrylonitrile Styrene Acrylate Blends for Outdoor Applications. Eng. J. 18 : 105-118.

Unar, I.N., Soomro, S.A. and Aziz, S. (2010). Effect of various additives on the physical properties of polyvinylchloride resin. Pak. J. Anal. Environ. Chem. 11(2) : 44-50.

Pita, V.J.R.R., Sampaio, E.E.M. and Monteiro, E.E.C. (2002). Mechanical properties evaluation of PVC/plasticizers and PVC/thermoplastic polyurethane blends from extrusion processing. Polym. Test. 21(5) : 545-550.

Si, Q.B., Zhou, C., Yang, H.D. and Zhang, H.X. (2007). Toughening of polyvinylchloride by core-shell rubber particles : influence of theinternal structure of core-shell particles. Eur. Polym. J. 43(7) : 3060-3067.

Zhou, L., Wang, X., Lin, Y., Yang, J. and Wu, Q. (2003). Comparison of the toughening mechanisms of poly(vinyl chloride)/chlorinated polyethylene and poly(vinyl chloride) /acrylonitrile-butadiene-styrene copolymer blends. J. Appl. Polym. Sci. 90(4) : 916-924.

Khanbabaei, G., Aalaie, J., Rahmatpour, A., Khoshniyat, A.and Gharabadian, M.A. (2007). Preparation and Properties of Epoxy-Clay Nanocomposites. J. Macromol. Sci., Part B: Phys. 46(5) : 975-986.

Takaki, A., Yasui, H. and Narisawa, I. (1997). Fracture and impact strength of poly (vinylchloride)/methyl methacrylate/ butadiene/styrene polymer blends. Polym. Eng. Sci. 37(1) : 105-119.

Dixit, M., Mathur, V., Gupta, S., Baboo, M., Sharma, K. and Saxena, N.S. (2009). Investigation of miscibility and mechanical properties of PMMA/PVC blends. J. Optoelectron. Adv. Mater. Rapid Commun. 3(10) : 1099-1105.

Soman, V.V. and Kelkar, D.S. (2009). FTIR Studies of Doped PMMA - PVC Blend System. Macromol. Symp. 277(1) : 152-161.

Aouachria, K. and Bensemra, N.B. (2006). Miscibility of PVC/PMMA blends by vicat softening temperature, viscometry, DSC and FTIR analysis. Polym. Test. 25(8) : 1101-1108.

Zhang, Z., Chen, S. and Zhang, J. (2013). Blends of poly (vinyl chloride) with α- methylstyrene – acrylonitrile - butadienestyrene copolymer: thermal Properties, mechanical properties and morphology. J. Vinyl. Addit. Techn. (1)19 : 1-10.

Zhang, Y.X., Xu, Y.J., Song, Y.H. and Zheng, Q. (2013). Study of poly(vinyl chloride)/ acrylonitrile – styrene – acrylate - acrylate blends for compatibility, toughness, thermal stability and UV irradiation. J. Appl. Polym. Sci. 130(3) : 2143-2151.

Downloads

Published

2014-11-28

How to Cite

[1]
B. . Saengiet, F. . Unob, and K. Srikulkit, “Effect of styrene-methyl methacrylate/styrene-butadiene rubber on properties of poly(vinyl chloride)”, J Met Mater Miner, vol. 24, no. 2, Nov. 2014.

Issue

Section

Original Research Articles

Most read articles by the same author(s)

<< < 1 2