Synchrotron X-ray tomography and functional evaluations of lead-free piezoceramic-filled natural rubber composites
DOI:
https://doi.org/10.55713/jmmm.v37i1.2650Keywords:
Flexible electronics, Lead-free piezoceramics, BCZT, Rubber composites, Synchrotron X-Ray TomographyAbstract
Flexible piezoelectric composite materials have gained increasing attention due to their widespread applications in modern electronic devices such as energy harvesters, dielectric capacitors, or wearable sensors. In this work, flexible piezoelectric composites were developed by incorporating BCZT lead-free piezoceramic fillers into a flexible NR matrix (NR/BCZT composites) with BCZT content ranging from 0 phr to 60 phr (referred as 0BCZT to 60BCZT). Additionally, the structure-property relationships of the NR/BCZT composites were evaluated using synchrotron X-ray tomographic microscopy (SR-XTM), in conjunction with various materials characterization techniques. This work found that the addition of BCZT filler into NR reduced cure time from 14.01 min (0BCZT) to 11.18 min (60BCZT), whereas hardness of the NR/BCZT composites increased from 40.18±0.08 to 45.92±0.11 with increasing BCZT content from 0 phr to 60 phr, respectively. Conversely, the tensile strength of the NR/BCZT composites at all compositions was lower than that of pure NR (tensile strength of 0BCZT = 24.70±2.56 MPa), except for the 30BCZT composite, which exhibited strong adhesion between the BCZT filler and the NR matrix and resulted in the observed highest tensile strength of 26.88±0.90 MPa. Interestingly, no increase in dielectric permittivity occurred at a low BCZT loading of 15 phr, while a significant enhancement from 2.76±0.13 to 3.34±0.08 was observed when the BCZT content was further increased from 15 phr to 30 phr, respectively. The filler dispersion in the NR matrix was investigated using synchrotron X-ray tomographic microscopy (SR-XTM), combined with quantitative analysis of SEM images. The results showed that, the interparticle spacing decreased with increasing the BCZT content in the NR/BCZT composites. This reduction in the interparticle spacing play an important role in the observed electrical properties of the NR/BCZT composites. These findings help to provide a better understanding of the development of lead-free piezoceramic-filled natural rubber composites.
Downloads
References
J. Rödel and J.-F. Li, "Lead-free piezoceramics: Status and perspectives," MRS Bulletin, vol. 43, no. 8, pp. 576‒580, 2018 DOI: https://doi.org/10.1557/mrs.2018.181
M. Smith, and S. Kar-Narayan, "Piezoelectric polymers: theory, challenges and opportunities," International Materials Reviews, vol. 67, no. 1, pp. 65‒88, 2022 DOI: https://doi.org/10.1080/09506608.2021.1915935
X. Li, G. Wu, C. Gao, R. Bao, and C. Pan, "Flexible electronic devices and wearable sensors based on liquid metals," MetalMat, vol. 2, no. 1, p. e70000, 2025. DOI: https://doi.org/10.1002/metm.70000
H. Hosseinzadeh, H. Oveisi, and K. Yazdani, "Review: Enhancing dielectric polymer performance via inorganic fillers," Journal of Materials Science, vol. 60, no. 42, pp. 20160‒20190, 2025. DOI: https://doi.org/10.1007/s10853-025-11536-8
L. Muhamad, M. A. Saparin, and H. Salleh, "Performance of a piezoelectric energy harvester with rubber compound modificatio," Journal of Physics: Conference Series, vol. 2721, p. 012002, 2024. DOI: https://doi.org/10.1088/1742-6596/2721/1/012002
J. E. Q. Quinsaat, T. de Wild, F. A. Nüesch, D. Damjanovic, R. Krämer, G. Schürch, D. Häfliger, F. Clemens, T. Sebastian, M. Dascalu, and D. M. Opris, "Stretchable piezoelectric elastic composites for sensors and energy generators," Composites Part B: Engineering, vol. 198, p. 108211, 2020. DOI: https://doi.org/10.1016/j.compositesb.2020.108211
J. Zhang, J. Wang, C. Zhong, Y. Zhang, Y. Qiu, and L. Qin, "Flexible electronics: Advancements and applications of flexible piezoelectric composites in modern sensing technologies," Micromachines, vol. 15, no. 8, p. 982, 2024. DOI: https://doi.org/10.3390/mi15080982
M. Mureddu, A. Reyes-Montero, S. Lopez-Esteban, J. F. Bartolome, S. Enzo, L. Pardo, and S. Garroni, "Hallmarks of BCZT-based piezoceramics: From chemical fundamental to processing route and biomedical applications," Boletín de la Sociedad Española de Cerámica y Vidrio, vol. 64, no. 3, p. 100434, 2025. DOI: https://doi.org/10.1016/j.bsecv.2025.01.003
S. Salaeh, N. Muensit, P. Bomlai, and C. Nakason, "Ceramic/ natural rubber composites: Influence types of rubber and ceramic materials on curing, mechanical, morphological, and dielectric properties," Journal of Materials Science, vol. 46, no. 6, pp. 1723‒1731, 2010. DOI: https://doi.org/10.1007/s10853-010-4990-6
N. González, M. d. À. Custal, G. N. Tomara, G. C. Psarras, J.-R. Riba, and E. Armelin, "Dielectric response of vulcanized natural rubber containing BaTiO3 filler: The role of particle functionalization," European Polymer Journal, vol. 97, pp. 57‒67, 2017. DOI: https://doi.org/10.1016/j.eurpolymj.2017.10.001
A. A. El-Gamal, "Electrical and mechanical characterization of vulcanized natural rubber filled with BaTiO3 ceramic filler," Journal of Thermoplastic Composite Materials, vol. 34, no. 3, pp. 287‒302, 2019. DOI: https://doi.org/10.1177/0892705719843160
L. Chen, W. Zhou, J. Lu, J. Li, W. Zhang, N. Huang, L.Wu, and L. Li, "Unveiling reinforcement and toughening mechanism of filler network in natural rubber with synchrotron radiation X-ray nano-computed tomography," Macromolecules, vol. 48, no. 21, pp. 7923‒7928, 2015. DOI: https://doi.org/10.1021/acs.macromol.5b01301
M. Matsubara, S. Teramoto, T. Komatsu, S. Furuta, M. Kobayashi, S. Kawamura, A. Nagatani, N. Tsujiuchi, and A. Ito, "Three-dimensional strain evaluation of short-fiber-reinforced natural rubber using micro X-ray computed tomography," Polymer Testing, vol. 111, Art. no. 107625, 2022. DOI: https://doi.org/10.1016/j.polymertesting.2022.107625
R. Mashita, Y. Bito, K. Uesugi, M. Hoshino, I. Kageyuki, H. Kishimoto, W. Yashiro, and T. Kanaya, "Insights into the cavitation morphology of rubber reinforced with a nano-filler," Scientific Reports, vol. 13, no. 1, Art. no. 5805, 2023. DOI: https://doi.org/10.1038/s41598-023-33137-8
A. P. Parra, M. Vlasova, and P. A. M. Aguilar, "Adsorptive properties of MgCO3–CaCO3 Sargasso treated in air and deficient of oxygen," MRS Advances, vol. 9, no. 3, pp. 148‒154, 2024. DOI: https://doi.org/10.1557/s43580-024-00813-4
M. Mureddu, J. F. Bartolomé, S. Lopez-Esteban, M. Dore, S. Enzo, Á. García, S. Garroni, and L. Pardo, "Solid state processing of BCZT piezoceramics using ultra low synthesis and sintering temperatures," Materials, vol. 16, no. 3, p. 945, 2023. DOI: https://doi.org/10.3390/ma16030945
S. Sahoo, U. Dash, S. K. S. Parashar, and S. M. Ali, "Frequency and temperature dependent electrical characteristics of CaTiO3 nano-ceramic prepared by high-energy ball milling," Journal of Advanced Ceramics, vol. 2, no. 3, pp. 291‒300, 2013. DOI: https://doi.org/10.1007/s40145-013-0075-8
X. W. Wang, B. H. Zhang, Y. Y. Li, Y. C. Shi, L. Y. Sun, G. Feng, C. L. Li, Y. F. Liang, Y. P. Zheng, S. Y. Shang, J. Shang, Y. C. Hu, and S. Q. Yin, "Structure, dielectric, and ferroelectric properties of Ba0.85Ca0.15Zr0.1Ti0.9O3 ceramics sintered at various temperatures," Journal of Materials Science: Materials in Electronics, vol. 31, no. 6, pp. 4732‒4742, 2020. DOI: https://doi.org/10.1007/s10854-020-03030-5
J. Intapun, T. Rungruang, S. Suchat, B. Cherdchim, and S. Hiziroglu, "The Characteristics of natural rubber composites with klason lignin as a green reinforcing filler: Thermal stability, mechanical and dynamical properties," Polymers, vol. 13, no. 7, p. 1109, 2021. DOI: https://doi.org/10.3390/polym13071109
T. T. M. Phan, N. C. Chu, V. B. Luu, H. N. Xuan, D. T. Pham, I. Martin, and P. Carrière, "Enhancement of polarization property of silane-modified BaTiO3 nanoparticles and its effect in increasing dielectric property of epoxy/BaTiO3 nano-composites," Journal of Science: Advanced Materials and Devices, vol. 1, no. 1, pp. 90‒97, 2016. DOI: https://doi.org/10.1016/j.jsamd.2016.04.005
M. Przybyszewska, and M. Zaborski, "The effect of zinc oxide nanoparticle morphology on activity in crosslinking of carboxylated nitrile elastomer," Express Polymer Letters, vol. 3, no. 9, pp. 542‒552, 2009. DOI: https://doi.org/10.3144/expresspolymlett.2009.68
E. Bayraktar, S. D. Antolovich, and C. Bathias, "New developments in non-destructive controls of the composite materials and applications in manufacturing engineering," Journal of Materials Processing Technology, vol. 206, no. 1‒3, pp. 30‒44, 2008. DOI: https://doi.org/10.1016/j.jmatprotec.2007.12.001
S. Konruang, A. Srisook, P. Buaphet, F. Tayeh, and W. Naebpetch, "Preparation of lead-free X-ray shielding materials based on natural rubber/barium sulfate composites," ASEAN Journal of Scientific and Technological Reports, vol. 25, no. 2, pp. 59‒66, 2022. DOI: https://doi.org/10.55164/ajstr.v25i2.246574
A. Lanna, M. Suklueng, C. Kasagepongsan, and S. Suchat, "Performance of novel engineered materials from epoxy resin with modified epoxidized natural rubber and nanocellulose or nanosilica," Advances in Polymer Technology, vol. 2020, no. 1, p. 2123836, 2020. DOI: https://doi.org/10.1155/2020/2123836
L. Caggiu, C. Cau, M.Mureddu, S. Enzo, F. Murgia, L. Pardo, S. Lopez-Esteban, J. F. Bartolomé, G. Mulas, R. Orrù, and S. Garroni, "High purity, crystallinity and electromechanical sensitivity of lead-free (Ba0.85Ca0.15)(Zr0.10Ti0.90)O3 synthesized using an EDTA/glycerol modified pechini method," Materials, vol. 18, no. 5, p. 1180, 2025. DOI: https://doi.org/10.3390/ma18051180
M. Mazaheri, A. M. Zahedi, and S. K. Sadrnezhaad, "Two-step sintering of nanocrystalline ZnO compacts: Effect of temperature on densification and grain growth," Journal of the American Ceramic Society, vol. 91, no. 1, pp. 56‒63, 2008. DOI: https://doi.org/10.1111/j.1551-2916.2007.02029.x
M. Stampanoni, R. Mokso, F. Marone, J. Vila-Comamala, S. Gorelick, P. Trtik, K. Jefimovs, and C. David, "Phase-contrast tomography at the nanoscale using hard x rays," Physical Review B, vol. 81, no. 14, p. 140105, 2010. DOI: https://doi.org/10.1103/PhysRevB.81.140105
C. A. Schneider, W. S. Rasband, K. W. Eliceiri, "NIH image to ImageJ: 25 years of image analysis," Nature Methods, vol. 9, pp. 671–675, 2012. DOI: https://doi.org/10.1038/nmeth.2089
ISO 13322-1:2014. Particle size analysis - Image analysis methods - Part 1: Static image analysis methods, 2014.
ISO 9276-2. Representation of results of particle size analysis - Part 2: Calculation of average particle sizes/diameters and moments from particle size distributions, 2014.
L. Dou, Y.-H. Lin, and C.-W. Nan, "An overview of linear dielectric polymers and their nanocomposites for energy storage," Molecules, vol. 26, no. 20, p. 6148, 2021. DOI: https://doi.org/10.3390/molecules26206148
Downloads
Published
How to Cite
Issue
Section
Categories
License
Copyright (c) 2026 Journal of Metals, Materials and Minerals

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Authors who publish in this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.




